Pixhawk Jetson Baseboard Bundle

Pixhawk Jetson Baseboard Bundle

Name: Pixhawk Jetson Baseboard Bundle с открытым исходным кодом
Availability: InStock

Артикул: Jetson Baseboard Bundle

Размеры: 48×33.6×16.3 mm

2x M.2 Key For WiFi/BT & NVMe SSD

Autopilot connected via UART,CAN and Ethernet Switch

Pixwark Autopilot BUS (PAB) Open Source Specification

Все характеристики

38,000.00 ₽ – 200,000.00 ₽

FC Module

Pixhawk 6X
Pixhawk 6X Pro
Pixhawk Jetson Baseboard Only

Companion Computer

Jetson Orin Nano 4GB (with Wi-Fi & SSD & Camera)
Jetson Orin NX 16GB (with Wi-Fi & SSD & Camera)

Aluminum Outer Case

With Case
Without Case

Очистить

Бесплатная доставка

Купить камеру и получить бесплатную доставку

Краткое обучение

Краткое обучение и техника безопасности

гарантия лучшей цены

лучшая цена от официального производителя

официальная гарантия

На всю продукцию представленную в магазине

Pixhawk Jetson Baseboard Bundle

Базовая плата Holybro Pixhawk Jetson основана на спецификации открытого стандарта шины автопилота Pixhawk (Pixhawk Autopilot Bus) и плате-носителе NVIDIA Jetson Orin NX/Nano. Форм-фактор шины автопилота Pixhawk (PAB) позволяет использовать эту плату с любым контроллером полета, совместимым с PAB, таким как Pixhawk 6X.

Feature

Combines the power of Pixhawk & Nvidia Jetson in a single board:
Nvidia Jetson & Pixhawk connected via UART, CAN, and ethernet switch
Pixhawk Autopilot Bus (PAB) Form Factor
Compatible with Jetson Orin NX & Orin Nano
2x M.@ key for WiFI/Bluetooth & NVMe SSD

Pixhawk 6X (ICM-45686)

Processors & Sensors
FMU Processor: STM32H753
- -32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
IO Processor: STM32F103
- -32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
On-board sensors (Shipping Currently, Rev8)
- -Accel/Gyro: 3x ICM-45686 (with BalancedGyro™ Technology)
- -Barometer: ICP20100 & BMP388
- -Mag: BMM150

UBEC-12A Specifications

Input voltage:
- 3~14S (XT30)
Output voltage:
- 6.0V
- 7.2V
- 8.0V
- 9.2V
- (recommend 7.2V if supplying power to Jetson Board)
Output Current:
- Continuous: 12A
- Burst: 24A
Size:
- 48×33.6×16.3 mm
Weight:
- 47.8g

Autopilot Connectors

Pixhawk Autopilot Bus Interface
- 100 Pin Hirose DF40
- 50 Pin Hirose DF40
Redundant Digital Power Module Inputs
- I2C Power Monitor Support
- 2x – 6 Pin Molex CLIK-Mate
- Power Path Selector w/ Overvoltage Protection
Voltage Ratings:
- Max input voltage: 6V
- USB Power Input: 4.75~5.25V
Full GPS Plus Safety Switch Port
- 10-Pin JST-GH
Secondary (GPS2) Port
- 6-pin JST-GH
2x CAN Ports
- 4 Pin JST-GH
3x Telemetry Ports with Flow Control
- 2x 6-Pin JST-GH
- 1 is connected to Jetson’s UART1 Port
16 PWM Outputs
- 2x 10-Pin JST-GH
UART4 & I2C Port
- 6-Pin JST-GH
2x Gigabit Ethernet port
- Connected to both Jetson & Autopilot via Ethernet switch (RTL8367S)
- 8-pin JST-GH
- RJ45
AD & IO
- 8-Pin JST-GH
USB 2.0
- USB-C
- 4-pin JST-GH
DSM Input
- 3-pin JST-ZH 1.5mm Pitch
RC in
- PPM/SBUS
- 5-pin JST-GH
SPI Port
- External Sensor Bus (SPI5)
- 11-Pin JST-GH
2x Debug Port
- 1 for FMU
- 1 for IO
- 10-Pin JST-SH
Dimensions (Without Jetson and Flight Controller Module)
- 126x80x38mm
Weight
- With Jetson, Heatsink, Flight Controller, M.2 SSD, M.2 Wi-Fi Module 203.2g

Baseboard Port & Connection

Jetson Connectors

2x Gigabit Ethernet port
- Connected to both Jetson & Autopilot via Ethernet switch (RTL8367S)
  - Ethernet Switch powered by circuit as the Pixhawk
- 8-pin JST-GH
- RJ45
2x MIPI CSI Camera Inputs
- 4 Lanes each
- 22-Pin Raspberry Pi Cam FFC
2x USB 3.0 Host Port
- USB A
- 5A Current Limit
2x USB 2.0 Host Port
- 5-Pin JST-GH
- 0A Current Limit
USB 2.0 for Programming/debugging
- USB-C
2 Key M 2242 for NVMe SSD
- PCIEx4
2 Key E 2230 for WiFi/BT
- PCIEx2
- USB
- UART
- I2S
Mini HDMI Out
4x GPIO
- 6-pin JST-GH
CAN Port
- Connected to Autopilot’s CAN2 (4 Pin JST-GH)
SPI Port
- 7-Pin JST-GH
I2C Port
- 4-Pin JST-GH
I2S Port
- 7-Pin JST-GH
2x UART Port
- 1 for debug
- 1 connected to Autopilot’s telem2
Fan Power Port
IIM42652 IMU
Input Power
- XT30 Connector
- Voltage Rating: 7-21V (3S-4S)
- Separate input power circuits than the Autopilot to ensure flight safety
- Holybro UBEC 12A (3-14S) can be used for application above 4S
- Note: The Pixhawk Jetson Baseboard onboard BEC is only rated for 7-21V (3S-4S). Using the external «UBEC 12A (3-14S)» can provides redundancy and easier replacement in case of BEC failure.
Power Requirements
- 8V/3A Minimum
- Depends on Usage and Peripherals

Pixhawk 6X (ICM-45686)

Processors & Sensors
FMU Processor: STM32H753
- -32 Bit Arm® Cortex®-M7, 480MHz, 2MB flash memory, 1MB RAM
IO Processor: STM32F103
- -32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
On-board sensors (Shipping Currently, Rev8)
- -Accel/Gyro: 3x ICM-45686 (with BalancedGyro™ Technology)
- -Barometer: ICP20100 & BMP388
- -Mag: BMM150

UBEC-12A Specifications

Input voltage:
- 3~14S (XT30)
Output voltage:
- 6.0V
- 7.2V
- 8.0V
- 9.2V
- (recommend 7.2V if supplying power to Jetson Board)
Output Current:
- Continuous: 12A
- Burst: 24A
Size:
- 48×33.6×16.3 mm
Weight:
- 47.8g

Autopilot Connectors

Pixhawk Autopilot Bus Interface
- 100 Pin Hirose DF40
- 50 Pin Hirose DF40
Redundant Digital Power Module Inputs
- I2C Power Monitor Support
- 2x – 6 Pin Molex CLIK-Mate
- Power Path Selector w/ Overvoltage Protection
Voltage Ratings:
- Max input voltage: 6V
- USB Power Input: 4.75~5.25V
Full GPS Plus Safety Switch Port
- 10-Pin JST-GH
Secondary (GPS2) Port
- 6-pin JST-GH
2x CAN Ports
- 4 Pin JST-GH
3x Telemetry Ports with Flow Control
- 2x 6-Pin JST-GH
- 1 is connected to Jetson’s UART1 Port
16 PWM Outputs
- 2x 10-Pin JST-GH
UART4 & I2C Port
- 6-Pin JST-GH
2x Gigabit Ethernet port
- Connected to both Jetson & Autopilot via Ethernet switch (RTL8367S)
- 8-pin JST-GH
- RJ45
AD & IO
- 8-Pin JST-GH
USB 2.0
- USB-C
- 4-pin JST-GH
DSM Input
- 3-pin JST-ZH 1.5mm Pitch
RC in
- PPM/SBUS
- 5-pin JST-GH
SPI Port
- External Sensor Bus (SPI5)
- 11-Pin JST-GH
2x Debug Port
- 1 for FMU
- 1 for IO
- 10-Pin JST-SH
Dimensions (Without Jetson and Flight Controller Module)
- 126x80x38mm
Weight
- With Jetson, Heatsink, Flight Controller, M.2 SSD, M.2 Wi-Fi Module 203.2g

Baseboard Port & Connection

Jetson Connectors

2x Gigabit Ethernet port
- Connected to both Jetson & Autopilot via Ethernet switch (RTL8367S)
  - Ethernet Switch powered by circuit as the Pixhawk
- 8-pin JST-GH
- RJ45
2x MIPI CSI Camera Inputs
- 4 Lanes each
- 22-Pin Raspberry Pi Cam FFC
2x USB 3.0 Host Port
- USB A
- 5A Current Limit
2x USB 2.0 Host Port
- 5-Pin JST-GH
- 0A Current Limit
USB 2.0 for Programming/debugging
- USB-C
2 Key M 2242 for NVMe SSD
- PCIEx4
2 Key E 2230 for WiFi/BT
- PCIEx2
- USB
- UART
- I2S
Mini HDMI Out
4x GPIO
- 6-pin JST-GH
CAN Port
- Connected to Autopilot’s CAN2 (4 Pin JST-GH)
SPI Port
- 7-Pin JST-GH
I2C Port
- 4-Pin JST-GH
I2S Port
- 7-Pin JST-GH
2x UART Port
- 1 for debug
- 1 connected to Autopilot’s telem2
Fan Power Port
IIM42652 IMU
Input Power
- XT30 Connector
- Voltage Rating: 7-21V (3S-4S)
- Separate input power circuits than the Autopilot to ensure flight safety
- Holybro UBEC 12A (3-14S) can be used for application above 4S
- Note: The Pixhawk Jetson Baseboard onboard BEC is only rated for 7-21V (3S-4S). Using the external «UBEC 12A (3-14S)» can provides redundancy and easier replacement in case of BEC failure.
Power Requirements
- 8V/3A Minimum
- Depends on Usage and Peripherals